Sunday, April 22, 2012
Hotwire Coupons
Thursday, September 1, 2011
STOP 0x0000007B Error Message and How to Remove It
What is the message STOP 0x0000007B:
When you start Microsoft Windows XP after replacing the motherboard of the computer, you may receive a Stop error message that is similar to the following:
STOP 0x0000007B INACCESSABLE_BOOT_DEVICE
STOP 0x0000007B error will always occur in a stop message, more commonly called Blue Screen of Death (BSOD). One of the mistakes below, or a combination of the two errors can be displayed in the message STOP:
"STOP: 0x0000007B"
"INACCESSIBLE_BOOT_DEVICE"
Why STOP 0x0000007B occurs:
This problem may occur if the new motherboard contains an integrated IDE controller that has a different chipset to the original motherboard.
STOP 0x0000007B errors are caused by problems with device drivers (especially those related to hard drive and other storage controllers), viruses, data corruption, and sometimes even hardware failures.
STOP 0x0000007B If the code is not required to stop watching or INACCESSIBLE_BOOT_DEVICE is not the message, please check my list of error codes and reference STOP information to troubleshoot STOP messages they see.
How to resolve STOP 0x0000007B:
To resolve this problem, use one of the following methods.
Note: Some of these steps may require that you access through Windows in Safe Mode. If that is not possible, then skip these steps.
1. Restart the computer if not already done so. The STOP 0x0000007B blue screen error may be a coincidence.
2. Did you just install or change to a hard disk controller? If so, there is a good chance that the change was the cause of STOP error 0x0000007B.
3. Undo the change and test the 0x7B blue screen error.
4. Depending on the changes you made, some solutions may include:
• Remove or reconfigure the newly installed driver disk.
• Start with the Last Known Good Configuration to undo the registry changes and driver related.
• Use System Restore to undo recent changes.
• Return hard disk controller device driver to the version before driver update.
3. Verify that the SCSI chain is terminated correctly, assuming you're using SCSI hard drives on your computer. Incorrect SCSI termination has been known to cause the STOP 0x0000007B error.
5. Check the hard disk is installed correctly. A hard drive installed incorrectly can cause STOP 0x0000007B error and other issues.
6. Verify that the hard drive is configured correctly in BIOS. STOP 0x0000007B error could occur if the hard drive settings in the BIOS is incorrect.
7. Scan your computer for viruses. Certain viruses that infect the master boot record (MBR) or boot sector may cause STOP 0x0000007B error.
Important: Make sure your antivirus software is updated and set to scan the MBR and boot sector.
7. Update the drivers for the hard disk controller. If the drivers for the hard disk controller are outdated, incorrect or damaged then STOP 0x0000007B can occur.
8. Change the SATA mode in BIOS to IDE mode. Disabling some of the advanced features of SATA in the BIOS could stop STOP 0x0000007B sample, especially if you're seeing in Windows XP or a Windows XP.
9. Run chkdsk on the hard disk. If the boot volume is corrupted, chkdsk can repair the damage.
10. Perform extensive testing of your hard drive. If your hard drive has a physical problem, a situation most likely is STOP 0x0000007B you are viewing. Replace the hard drive if the diagnosis is completed suggest a hardware problem with the unit.
11. Run the fixmbr command to create a master boot record. A damaged master boot record could be the cause of STOP error 0x0000007B.
12. To clear the CMOS. Sometimes STOP 0x0000007B is caused by a BIOS memory problem. Clearing the CMOS could solve that problem.
13. Update your BIOS. In some situations, an outdated BIOS may cause a STOP 0x0000007B because of incompatibilities with a hard disk controller.
14. Update firmware on the hard disk controller if possible. As with the BIOS in the previous step, an inconsistency that could be causing the error 0x7B and a manufacturer's firmware update to fix the problem.
15. Repair installation of Windows. If you just replace the motherboard on a computer without having to reinstall Windows, then it is likely that this solves your problem.
16. Perform basic troubleshooting STOP error. If none of the above specific steps to help solve STOP 0x0000007B you're watching, take a look at this troubleshooting guide shut-off error. Like most of the STOP errors are also caused some of the suggestions that can help.
Dell Optiplex 330 users receiving STOP 0x0000007B (0xF78DA63C, 0x0000034, 0X x0000000, 0x0000000 error message, the problem can be solved by the following way:
1. At startup (Dell logo), press F2 to enter BIOS
2. Expand the "Drives" section
3. Go to "SATA Operation"
4. Changing this to "Auto RAID / AHCI" to "RAID Auto / ATA"